Shipping Update: Custom 100L Vacuum Screw Discharge Kneader Heading to Epoxy Resin Facility

Publish Time: 2026-01-15 Origin: Site

This morning, we finalized the crating for a specialized 100L Vacuum Screw Discharge Kneader. This unit is now on its way to a client specializing in Epoxy Resins and high-performance additives.

Before this machine leaves our dock, we wanted to share a quick case study on why this specific configuration is often the "Gold Standard" for processing temperature-sensitive, high-viscosity chemicals.

If you are struggling with mixing heavy pastes or worrying about material curing inside the bowl, this post is for you.

The Challenge: Why Epoxy Resin is Tough to Mix

Anyone in the resin industry knows that mixing epoxy isn't just about stirring; it's about managing viscosity and heat.

High Viscosity: At room temperature, resin and additives can be extremely thick. Standard mixers often leave "dead spots" where the hardener or conductive powders don't disperse properly.
The Heat Problem (Exotherm): The friction from mixing heavy materials generates significant mechanical heat. If you don't control this heat, the epoxy can start to cross-link (cure) prematurely inside the mixer. That is an expensive disaster.

Our client needed a solution that could handle the heavy load and keep the temperature strictly under control.

Machine Configuration: Built for the Job

This 100L unit is a pilot-scale production machine, but it is built with the heavy-duty specs of our larger 1000L lines. Here is the breakdown of the solution:

1. Heavy-Duty Sigma (Σ) Blades

We utilized a reinforced Z-arm (Sigma) blade design. These blades rotate at differential speeds, creating intense shearing and folding actions. This ensures that even the most stubborn additives are thoroughly kneaded into the resin matrix without any unmixed lumps.

2. Integrated Industrial Chiller & Jacketed Bowl

This is the critical safety feature for this project.
Instead of relying on standard tap water cooling, we supplied a dedicated Industrial Water Chiller. The kneader bowl features a double-layer jacket. The chiller circulates coolant through this jacket in a closed loop, aggressively removing the heat generated by friction.

Result: The material temperature remains stable, preventing premature curing or degradation during the mixing cycle.

3. Screw Discharge (Extrusion)

Old-school kneaders use a "Hydraulic Tilt" to dump the batch. For sticky epoxy, that is a nightmare—you end up scraping the bowl by hand for an hour.
This machine features a bottom discharge screw:

During Mixing: The screw runs in reverse, pushing material back into the mixing zone to ensure homogeneity.
During Discharge: The screw runs forward, extruding the sticky material directly out through a die.
Advantage: This allows for a sealed process (no air bubbles introduced during discharge) and connects easily to downstream filling lines.

Why No Vacuum Pump? (A Note on Customization)

Sharp-eyed engineers might notice the vacuum ports on the machine but the absence of a vacuum pump in the shipping list.

This wasn't an oversight. It was a strategic cost-saving choice for the client.

The client's facility already operates a powerful central vacuum system. Instead of forcing them to buy a standalone pump they didn't need, we customized the machine with standard DN vacuum flanges to interface directly with their existing piping.
We believe in adapting our equipment to your factory, not the other way around.

The FAT (Factory Acceptance Test)

We never ship metal until it’s proven to work. Yesterday’s FAT included:

Vacuum Hold Test: Pressurized the jacket and pulled vacuum on the bowl to ensure perfect sealing (crucial for bubble-free resin).
Clearance Check: Verified the gap between the screw and the barrel to ensure efficient self-cleaning without metal-on-metal contact.
Load Simulation: Ran the drive system to monitor gearbox noise and bearing temperatures.

Ready for Your Project?

Equipment for chemical processing looks similar on the outside, but the difference lies in the details—the seal reliability, the cooling efficiency, and the torque.

If you are dealing with high-viscosity materials, difficult discharge processes, or temperature sensitivity, let’s talk. We don't just sell machines; we help optimize your process.

The truck is leaving, and we are ready for the next build.

info@karvil.com